Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/gi…

…t/torvalds/linux

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -151,6 +151,65 @@ Example:
 		clocks = <&clk32k>;
 	};
 
+SHDWC SAMA5D2-Compatible Shutdown Controller
+
+1) shdwc node
+
+required properties:
+- compatible: should be "atmel,sama5d2-shdwc".
+- reg: should contain registers location and length
+- clocks: phandle to input clock.
+- #address-cells: should be one. The cell is the wake-up input index.
+- #size-cells: should be zero.
+
+optional properties:
+
+- debounce-delay-us: minimum wake-up inputs debouncer period in
+  microseconds. It's usually a board-related property.
+- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up.
+
+The node contains child nodes for each wake-up input that the platform uses.
+
+2) input nodes
+
+Wake-up input nodes are usually described in the "board" part of the Device
+Tree. Note also that input 0 is linked to the wake-up pin and is frequently
+used.
+
+Required properties:
+- reg: should contain the wake-up input index [0 - 15].
+
+Optional properties:
+- atmel,wakeup-active-high: boolean, the corresponding wake-up input described
+  by the child, forces the wake-up of the core power supply on a high level.
+  The default is to be active low.
+
+Example:
+
+On the SoC side:
+	shdwc@f8048010 {
+		compatible = "atmel,sama5d2-shdwc";
+		reg = <0xf8048010 0x10>;
+		clocks = <&clk32k>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		atmel,wakeup-rtc-timer;
+	};
+
+On the board side:
+	shdwc@f8048010 {
+		debounce-delay-us = <976>;
+
+		input@0 {
+			reg = <0>;
+		};
+
+		input@1 {
+			reg = <1>;
+			atmel,wakeup-active-high;
+		};
+	};
+
 Special Function Registers (SFR)
 
 Special Function Registers (SFR) manage specific aspects of the integrated

Documentation/devicetree/bindings/arm/cci.txt

@@ -100,7 +100,7 @@ specific to ARM.
 				 "arm,cci-400-pmu,r0"
 				 "arm,cci-400-pmu,r1"
 				 "arm,cci-400-pmu"  - DEPRECATED, permitted only where OS has
-						      secure acces to CCI registers
+						      secure access to CCI registers
 				 "arm,cci-500-pmu,r0"
 				 "arm,cci-550-pmu,r0"
 		- reg:

Documentation/devicetree/bindings/arm/omap/crossbar.txt

@@ -42,7 +42,8 @@ Examples:
 Consumer:
 ========
 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt and
-Documentation/devicetree/bindings/arm/gic.txt for further details.
+Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt for
+further details.
 
 An interrupt consumer on an SoC using crossbar will use:
 	interrupts = <GIC_SPI request_number interrupt_level>

Documentation/devicetree/bindings/arm/spear-misc.txt

@@ -6,4 +6,4 @@ few properties of different peripheral controllers.
 misc node required properties:
 
 - compatible Should be	"st,spear1340-misc", "syscon".
-- reg: Address range of misc space upto 8K
+- reg: Address range of misc space up to 8K

Documentation/devicetree/bindings/arm/ux500/boards.txt

@@ -23,7 +23,7 @@ scu:
 	see binding for arm/scu.txt
 
 interrupt-controller:
-	see binding for arm/gic.txt
+	see binding for interrupt-controller/arm,gic.txt
 
 timer:
 	see binding for arm/twd.txt

Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt

@@ -50,7 +50,7 @@ Required properties for I2C mode:
 
 Example:
 
-clock@0,70110000 {
+clock@70110000 {
         compatible = "nvidia,tegra124-dfll";
         reg = <0 0x70110000 0 0x100>, /* DFLL control */
               <0 0x70110000 0 0x100>, /* I2C output control */

Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt

@@ -16,7 +16,7 @@ Required Properties:
 Optional Properties:
 
 - rockchip,grf: phandle to the syscon managing the "general register files"
-  If missing pll rates are not changable, due to the missing pll lock status.
+  If missing pll rates are not changeable, due to the missing pll lock status.
 
 Each clock is assigned an identifier and client nodes can use this identifier
 to specify the clock which they consume. All available clocks are defined as

Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt

@@ -15,7 +15,7 @@ Required Properties:
 Optional Properties:
 
 - rockchip,grf: phandle to the syscon managing the "general register files"
-  If missing pll rates are not changable, due to the missing pll lock status.
+  If missing pll rates are not changeable, due to the missing pll lock status.
 
 Each clock is assigned an identifier and client nodes can use this identifier
 to specify the clock which they consume. All available clocks are defined as

Documentation/devicetree/bindings/clock/st/st,clkgen.txt

@@ -40,7 +40,7 @@ address is common of all subnode.
 	};
 
 This binding uses the common clock binding[1].
-Each subnode should use the binding discribe in [2]..[7]
+Each subnode should use the binding described in [2]..[7]
 
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/clock/st,clkgen-divmux.txt

Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt

@@ -41,7 +41,7 @@ Video interfaces:
   endpoint node connected from mic node (reg = 0):
     - remote-endpoint: specifies the endpoint in mic node. This node is required
 		       for Exynos5433 mipi dsi. So mic can access to panel node
-		       thoughout this dsi node.
+		       throughout this dsi node.
   endpoint node connected to panel node (reg = 1):
     - remote-endpoint: specifies the endpoint in panel node. This node is
 		       required in all kinds of exynos mipi dsi to represent

Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt

@@ -7,7 +7,7 @@ Required properties:
 - compatible: Should be "xlnx,axi-dma-1.00.a"
 - #dma-cells: Should be <1>, see "dmas" property below
 - reg: Should contain DMA registers location and length.
-- dma-channel child node: Should have atleast one channel and can have upto
+- dma-channel child node: Should have at least one channel and can have up to
 	two channels per device. This node specifies the properties of each
 	DMA channel (see child node properties below).
 

Documentation/devicetree/bindings/gpio/ibm,ppc4xx-gpio.txt

@@ -0,0 +1,24 @@
+* IBM/AMCC/APM GPIO Controller for PowerPC 4XX series and compatible SoCs
+
+All GPIOs are pin-shared with other functions. DCRs control whether a
+particular pin that has GPIO capabilities acts as a GPIO or is used for
+another purpose. GPIO outputs are separately programmable to emulate
+an open-drain driver.
+
+Required properties:
+	- compatible: must be "ibm,ppc4xx-gpio"
+	- reg: address and length of the register set for the device
+	- #gpio-cells: must be set to 2. The first cell is the pin number
+		and the second cell is used to specify the gpio polarity:
+		0 = active high
+		1 = active low
+	- gpio-controller: marks the device node as a gpio controller.
+
+Example:
+
+GPIO0: gpio@ef600b00 {
+	compatible = "ibm,ppc4xx-gpio";
+	reg = <0xef600b00 0x00000048>;
+	#gpio-cells = <2>;
+	gpio-controller;
+};

Documentation/devicetree/bindings/input/ads7846.txt

@@ -29,7 +29,7 @@ Optional properties:
 	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
 					external vref (u16).
 	ti,vref-mv			The VREF voltage, in millivolts (u16).
-					Set to 0 to use internal refernce
+					Set to 0 to use internal references
 					(ADS7846).
 	ti,keep-vref-on			set to keep vref on for differential
 					measurements as well

Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt

@@ -15,7 +15,7 @@ Optional properties:
  - fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
  - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
    between 1 and 4096. It is the ratio between the internal reference voltage
-   and the measured voltage after the plate was precharged. Resistence between
+   and the measured voltage after the plate was precharged. Resistance between
    plates and therefore the voltage decreases with pressure so that a smaller
    value is equivalent to a higher pressure.
  - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before

Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt

@@ -16,8 +16,7 @@ Required properties:
 	"mediatek,mt6577-sysirq"
 	"mediatek,mt2701-sysirq"
 - interrupt-controller : Identifies the node as an interrupt controller
-- #interrupt-cells : Use the same format as specified by GIC in
-  Documentation/devicetree/bindings/arm/gic.txt
+- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
 - interrupt-parent: phandle of irq parent for sysirq. The parent must
   use the same interrupt-cells format as GIC.
 - reg: Physical base address of the intpol registers and length of memory

Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu

@@ -4,7 +4,7 @@ All TI OMAP4/5 (and their derivatives) an interrupt controller that
 routes interrupts to the GIC, and also serves as a wakeup source. It
 is also referred to as "WUGEN-MPU", hence the name of the binding.
 
-Reguired properties:
+Required properties:
 
 - compatible : should contain at least "ti,omap4-wugen-mpu" or
   "ti,omap5-wugen-mpu"
@@ -20,7 +20,7 @@ Notes:
 - Because this HW ultimately routes interrupts to the GIC, the
   interrupt specifier must be that of the GIC.
 - Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs
-  are explicitly forbiden.
+  are explicitly forbidden.
 
 Example:
 

Documentation/devicetree/bindings/memory-controllers/tegra-emc.txt → Documentation/devicetree/bindings/memory-controllers/nvidia,tegra124-emc.txt

@@ -190,7 +190,7 @@ be specified, according to the board documentation:
 Example SoC include file:
 
 / {
-	emc@0,7001b000 {
+	emc@7001b000 {
 		compatible = "nvidia,tegra124-emc";
 		reg = <0x0 0x7001b000 0x0 0x1000>;
 
@@ -201,7 +201,7 @@ Example SoC include file:
 Example board file:
 
 / {
-	emc@0,7001b000 {
+	emc@7001b000 {
 		emc-timings-3 {
 			nvidia,ram-code = <3>;
 

Documentation/devicetree/bindings/memory-controllers/nvidia,tegra-mc.txt → Documentation/devicetree/bindings/memory-controllers/nvidia,tegra30-mc.txt

@@ -61,7 +61,7 @@ specified, according to the board documentation:
 Example SoC include file:
 
 / {
-	mc: memory-controller@0,70019000 {
+	mc: memory-controller@70019000 {
 		compatible = "nvidia,tegra124-mc";
 		reg = <0x0 0x70019000 0x0 0x1000>;
 		clocks = <&tegra_car TEGRA124_CLK_MC>;
@@ -72,7 +72,7 @@ Example SoC include file:
 		#iommu-cells = <1>;
 	};
 
-	sdhci@0,700b0000 {
+	sdhci@700b0000 {
 		compatible = "nvidia,tegra124-sdhci";
 		...
 		iommus = <&mc TEGRA_SWGROUP_SDMMC1A>;
@@ -82,7 +82,7 @@ Example SoC include file:
 Example board file:
 
 / {
-	memory-controller@0,70019000 {
+	memory-controller@70019000 {
 		emc-timings-3 {
 			nvidia,ram-code = <3>;
 

Documentation/devicetree/bindings/mfd/qcom-rpm.txt

@@ -178,7 +178,7 @@ see regulator.txt - with additional custom properties described below:
 - qcom,force-mode:
 	Usage: optional (default if no other qcom,force-mode is specified)
 	Value type: <u32>
-	Defintion: indicates that the regulator should be forced to a
+	Definition: indicates that the regulator should be forced to a
 		   particular mode, valid values are:
 		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
@@ -204,7 +204,7 @@ see regulator.txt - with additional custom properties described below:
 - qcom,force-mode:
 	Usage: optional
 	Value type: <u32>
-	Defintion: indicates that the regulator should not be forced to any
+	Definition: indicates that the regulator should not be forced to any
 		   particular mode, valid values are:
 		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode

Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.txt

@@ -1,7 +1,7 @@
 * The simple eMMC hardware reset provider
 
 The purpose of this driver is to perform standard eMMC hw reset
-procedure, as descibed by Jedec 4.4 specification. This procedure is
+procedure, as described by Jedec 4.4 specification. This procedure is
 performed just after MMC core enabled power to the given mmc host (to
 fix possible issues if bootloader has left eMMC card in initialized or
 unknown state), and before performing complete system reboot (also in

Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

@@ -52,7 +52,7 @@ Optional properties:
                               v7.0. Use this property to describe the rare
                               earlier versions of this core that include WP
 
- -- Additonal SoC-specific NAND controller properties --
+ -- Additional SoC-specific NAND controller properties --
 
 The NAND controller is integrated differently on the variety of SoCs on which it
 is found. Part of this integration involves providing status and enable bits

Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt

@@ -8,7 +8,7 @@ Required properties:
   specifies a reference to the associating hardware driver node.
   see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt
 - port-id: is the index of port provided by DSAF (the accelerator). DSAF can
-  connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They
+  connect to 8 PHYs. Port 0 to 1 are both used for administration purpose. They
   are called debug ports.
 
   The remaining 6 PHYs are taken according to the mode of DSAF.

Documentation/devicetree/bindings/net/stmmac.txt

@@ -51,8 +51,8 @@ Optional properties:
 			   AXI register inside the DMA module:
 	- snps,lpi_en: enable Low Power Interface
 	- snps,xit_frm: unlock on WoL
-	- snps,wr_osr_lmt: max write oustanding req. limit
-	- snps,rd_osr_lmt: max read oustanding req. limit
+	- snps,wr_osr_lmt: max write outstanding req. limit
+	- snps,rd_osr_lmt: max read outstanding req. limit
 	- snps,kbbe: do not cross 1KiB boundary.
 	- snps,axi_all: align address
 	- snps,blen: this is a vector of supported burst length.

Documentation/devicetree/bindings/net/ti,dp83867.txt

@@ -2,7 +2,7 @@
 
 Required properties:
 	- reg - The ID number for the phy, usually a small integer
-	- ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h
+	- ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h
 		for applicable values
 	- ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h
 		for applicable values

Documentation/devicetree/bindings/opp/opp.txt

@@ -45,7 +45,7 @@ Devices supporting OPPs must set their "operating-points-v2" property with
 phandle to a OPP table in their DT node. The OPP core will use this phandle to
 find the operating points for the device.
 
-If required, this can be extended for SoC vendor specfic bindings. Such bindings
+If required, this can be extended for SoC vendor specific bindings. Such bindings
 should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt
 and should have a compatible description like: "operating-points-v2-<vendor>".
 

Documentation/devicetree/bindings/pci/designware-pcie.txt

@@ -31,7 +31,7 @@ Optional properties:
 
 Example configuration:
 
-	pcie: pcie@0xdffff000 {
+	pcie: pcie@dffff000 {
 		compatible = "snps,dw-pcie";
 		reg = <0xdffff000 0x1000>, /* Controller registers */
 		      <0xd0000000 0x2000>; /* PCI config space */

Documentation/devicetree/bindings/pci/hisilicon-pcie.txt

@@ -34,11 +34,11 @@ Hip05 Example (note that Hip06 is the same except compatible):
 		ranges = <0x82000000 0 0x00000000 0x220 0x00000000 0 0x10000000>;
 		num-lanes = <8>;
 		port-id = <1>;
-		#interrupts-cells = <1>;
-		interrupts-map-mask = <0xf800 0 0 7>;
-		interrupts-map = <0x0 0 0 1 &mbigen_pcie 1 10
-				  0x0 0 0 2 &mbigen_pcie 2 11
-				  0x0 0 0 3 &mbigen_pcie 3 12
-				  0x0 0 0 4 &mbigen_pcie 4 13>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <0x0 0 0 1 &mbigen_pcie 1 10
+				 0x0 0 0 2 &mbigen_pcie 2 11
+				 0x0 0 0 3 &mbigen_pcie 3 12
+				 0x0 0 0 4 &mbigen_pcie 4 13>;
 		status = "ok";
 	};

Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt

@@ -17,7 +17,7 @@ Example:
 
 usb2_phy: usb2phy@0 {
 	compatible	= "st,stih416-usb-phy";
-	#phy-cell	= <0>;
+	#phy-cells	= <0>;
 	st,syscfg	= <&syscfg_rear>;
 	clocks		= <&clk_sysin>;
 	clock-names	= "osc_phy";