[JTC] Rename open_loop_control parameter and slightly change its scope

doc/migration.rst

@@ -20,3 +20,4 @@ joint_trajectory_controller
 * Angle wraparound behavior (continuous joints) was added from the current state to the first segment of the incoming trajectory (`#796 <https://github.com/ros-controls/ros2_controllers/pull/796>`_).
 * The URDF is now parsed for continuous joints and angle wraparound is automatically activated now (`#949 <https://github.com/ros-controls/ros2_controllers/pull/949>`_). Remove the ``angle_wraparound`` parameter from the configuration and set continuous joint type in the URDF of the respective joint.
 * Tolerances sent with the action goal were not used before, but are now processed and used for the upcoming action. (`#716 <https://github.com/ros-controls/ros2_controllers/pull/716>`_). Adaptions to the action goal might be necessary.
+* Parameter ``open_loop_control`` is replaced by ``interpolate_from_desired_state`` and setting the feedback gains to zero (`#1525 <https://github.com/ros-controls/ros2_controllers/pull/1525>`_).

doc/release_notes.rst

@@ -52,6 +52,7 @@ joint_trajectory_controller
             allowed to move without restriction.
 
 * Add the boolean parameter ``set_last_command_interface_value_as_state_on_activation``. When set to ``true``, the last command interface value is used as both the current state and the last commanded state upon activation. When set to ``false``, the current state is used for both (`#1231 <https://github.com/ros-controls/ros2_controllers/pull/1231>`_).
+* Parameter ``open_loop_control`` is replaced by ``interpolate_from_desired_state`` and setting the feedback gains to zero (`#1525 <https://github.com/ros-controls/ros2_controllers/pull/1525>`_).
 
 mecanum_drive_controller
 ************************

joint_trajectory_controller/doc/parameters_context.yaml

@@ -2,8 +2,6 @@ constraints:
     Default values for tolerances if no explicit values are set in the ``JointTrajectory`` message.
 
 gains: |
-  Only relevant, if ``open_loop_control`` is not set.
-
   If ``velocity`` is the only command interface for all joints or an ``effort`` command interface is configured, PID controllers are used for every joint.
   This structure contains the controller gains for every joint with the control law
 
@@ -16,3 +14,5 @@ gains: |
   i.e., the shortest rotation to the target position is the desired motion.
   Otherwise  :math:`e = s_d - s` is used, with the desired position :math:`s_d` and the measured
   position :math:`s` from the state interface.
+
+  If you want to turn off the PIDs (open loop control), set the feedback gains to zero.

joint_trajectory_controller/doc/userdoc.rst

@@ -97,7 +97,7 @@ A yaml file for using it could be:
           action_monitor_rate: 20.0
 
           allow_partial_joints_goal: false
-          open_loop_control: true
+          interpolate_from_desired_state: true
           constraints:
             stopped_velocity_tolerance: 0.01
             goal_time: 0.0

joint_trajectory_controller/src/joint_trajectory_controller.cpp

@@ -192,7 +192,7 @@ controller_interface::return_type JointTrajectoryController::update(
     if (!traj_external_point_ptr_->is_sampled_already())
     {
       first_sample = true;
-      if (params_.open_loop_control)
+      if (params_.interpolate_from_desired_state || params_.open_loop_control)
       {
         traj_external_point_ptr_->set_point_before_trajectory_msg(
           time, last_commanded_state_, joints_angle_wraparound_);
@@ -661,6 +661,16 @@ controller_interface::CallbackReturn JointTrajectoryController::on_configure(
     return controller_interface::CallbackReturn::ERROR;
   }
 
+  // START DEPRECATE
+  if (params_.open_loop_control)
+  {
+    RCLCPP_WARN(
+      logger,
+      "[deprecated] 'open_loop_control' parameter is deprecated. Instead, set the feedback gains "
+      "to zero and use 'interpolate_from_desired_state' parameter");
+  }
+  // END DEPRECATE
+
   // update the dynamic map parameters
   param_listener_->refresh_dynamic_parameters();
 

joint_trajectory_controller/src/joint_trajectory_controller_parameters.yaml

@@ -47,12 +47,18 @@ joint_trajectory_controller:
   open_loop_control: {
     type: bool,
     default_value: false,
-    description: "Use controller in open-loop control mode
+    description: "deprecated: use interpolate_from_desired_state and set feedback gains to zero instead",
+    read_only: true,
+  }
+  interpolate_from_desired_state: {
+    type: bool,
+    default_value: false,
+    description: "Interpolate from the current desired state when receiving a new trajectory.
       \n\n
       * The controller ignores the states provided by hardware interface but using last commands as states for starting the trajectory interpolation.\n
-      * It deactivates the feedback control, see the ``gains`` structure.
       \n\n
       This is useful if hardware states are not following commands, i.e., an offset between those (typical for hydraulic manipulators).
+      Furthermore, it is necessary if you have a reference trajectory that you send over multiple messages (e.g. for MPC-style trajectory planning).
       \n\n
       If this flag is set, the controller tries to read the values from the command interfaces on activation.
       If they have real numeric values, those will be used instead of state interfaces.

joint_trajectory_controller/test/test_trajectory_controller.cpp

@@ -1005,8 +1005,7 @@ TEST_P(TrajectoryControllerTestParameterized, use_closed_loop_pid)
     (traj_controller_->has_velocity_command_interface() &&
      !traj_controller_->has_position_command_interface() &&
      !traj_controller_->has_effort_command_interface() &&
-     !traj_controller_->has_acceleration_command_interface() &&
-     !traj_controller_->is_open_loop()) ||
+     !traj_controller_->has_acceleration_command_interface()) ||
     traj_controller_->has_effort_command_interface())
   {
     EXPECT_TRUE(traj_controller_->use_closed_loop_pid_adapter());
@@ -1685,8 +1684,8 @@ TEST_P(TrajectoryControllerTestParameterized, test_jump_when_state_tracking_erro
 {
   rclcpp::executors::SingleThreadedExecutor executor;
   // default if false so it will not be actually set parameter
-  rclcpp::Parameter is_open_loop_parameters("open_loop_control", false);
-  SetUpAndActivateTrajectoryController(executor, {is_open_loop_parameters}, true);
+  rclcpp::Parameter interp_desired_state_parameter("interpolate_from_desired_state", false);
+  SetUpAndActivateTrajectoryController(executor, {interp_desired_state_parameter}, true);
 
   if (traj_controller_->has_position_command_interface() == false)
   {
@@ -1790,10 +1789,10 @@ TEST_P(TrajectoryControllerTestParameterized, test_no_jump_when_state_tracking_e
 {
   rclcpp::executors::SingleThreadedExecutor executor;
   // set open loop to true, this should change behavior from above
-  rclcpp::Parameter is_open_loop_parameters("open_loop_control", true);
+  rclcpp::Parameter interp_desired_state_parameter("interpolate_from_desired_state", true);
   rclcpp::Parameter update_rate_param("update_rate", 100);
   SetUpAndActivateTrajectoryController(
-    executor, {is_open_loop_parameters, update_rate_param}, true);
+    executor, {interp_desired_state_parameter, update_rate_param}, true);
 
   if (traj_controller_->has_position_command_interface() == false)
   {
@@ -1893,15 +1892,15 @@ TEST_P(TrajectoryControllerTestParameterized, test_no_jump_when_state_tracking_e
 TEST_P(TrajectoryControllerTestParameterized, test_hw_states_has_offset_first_controller_start)
 {
   rclcpp::executors::SingleThreadedExecutor executor;
-  rclcpp::Parameter is_open_loop_parameters("open_loop_control", true);
+  rclcpp::Parameter interp_desired_state_parameter("interpolate_from_desired_state", true);
 
   // set command values to NaN
   std::vector<double> initial_pos_cmd{3, std::numeric_limits<double>::quiet_NaN()};
   std::vector<double> initial_vel_cmd{3, std::numeric_limits<double>::quiet_NaN()};
   std::vector<double> initial_acc_cmd{3, std::numeric_limits<double>::quiet_NaN()};
 
   SetUpAndActivateTrajectoryController(
-    executor, {is_open_loop_parameters}, true, 0., 1., initial_pos_cmd, initial_vel_cmd,
+    executor, {interp_desired_state_parameter}, true, 0., 1., initial_pos_cmd, initial_vel_cmd,
     initial_acc_cmd);
 
   // no call of update method, so the values should be read from state interfaces
@@ -1934,7 +1933,7 @@ TEST_P(TrajectoryControllerTestParameterized, test_hw_states_has_offset_first_co
 TEST_P(TrajectoryControllerTestParameterized, test_hw_states_has_offset_later_controller_start)
 {
   rclcpp::executors::SingleThreadedExecutor executor;
-  rclcpp::Parameter is_open_loop_parameters("open_loop_control", true);
+  rclcpp::Parameter interp_desired_state_parameter("interpolate_from_desired_state", true);
 
   // set command values to arbitrary values
   std::vector<double> initial_pos_cmd, initial_vel_cmd, initial_acc_cmd;
@@ -1945,7 +1944,7 @@ TEST_P(TrajectoryControllerTestParameterized, test_hw_states_has_offset_later_co
     initial_acc_cmd.push_back(0.02 + static_cast<double>(i) / 10.0);
   }
   SetUpAndActivateTrajectoryController(
-    executor, {is_open_loop_parameters}, true, 0., 1., initial_pos_cmd, initial_vel_cmd,
+    executor, {interp_desired_state_parameter}, true, 0., 1., initial_pos_cmd, initial_vel_cmd,
     initial_acc_cmd);
 
   // no call of update method, so the values should be read from command interfaces

joint_trajectory_controller/test/test_trajectory_controller_utils.hpp

@@ -167,7 +167,9 @@ class TestableJointTrajectoryController
 
   bool use_closed_loop_pid_adapter() const { return use_closed_loop_pid_adapter_; }
 
+  // START DEPRECATE
   bool is_open_loop() const { return params_.open_loop_control; }
+  // END DEPRECATE
 
   joint_trajectory_controller::SegmentTolerances get_active_tolerances()
   {