Change heater thermistor table to mitigate Klipper3d/klipper#4054

Add smartplug shutdown service to git repo
Update meshes after bed disassembly/reassembly.

heaters.cfg

@@ -3,7 +3,7 @@ nozzle_diameter: 0.400
 filament_diameter: 1.75
 ##      In E0 OUT Position
 heater_pin: PB15
-sensor_type: NTC 100K beta 3950
+sensor_type: EPCOS 100K B57560G104F # See https://github.com/KevinOConnor/klipper/issues/4054
 sensor_pin: PC0
 min_temp: 5
 max_temp: 295
@@ -23,7 +23,7 @@ sensor_type: NTC 100K MGB18-104F39050L32
 sensor_pin: PC3
 ##	Adjust Max Power so your heater doesn't warp your bed
 max_power: 0.75
-min_temp: -100
+min_temp: 0
 max_temp: 125
 control: pid
 
@@ -51,3 +51,12 @@ sensor_type: temperature_mcu
 
 [temperature_sensor pi]
 sensor_type: temperature_host
+
+## 	Thermistor Types
+##   "EPCOS 100K B57560G104F"
+##   "ATC Semitec 104GT-2"
+##   "NTC 100K beta 3950"
+##   "Honeywell 100K 135-104LAG-J01"
+##   "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
+##   "AD595"
+##   "PT100 INA826"

printer.cfg

@@ -67,15 +67,6 @@ path: /home/pi/gcode_files
 [force_move]
 enable_force_move: true
 
-## 	Thermistor Types
-##   "EPCOS 100K B57560G104F"
-##   "ATC Semitec 104GT-2"
-##   "NTC 100K beta 3950"
-##   "Honeywell 100K 135-104LAG-J01"
-##   "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
-##   "AD595"
-##   "PT100 INA826"
-
 #*# <---------------------- SAVE_CONFIG ---------------------->
 #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
 #*#
@@ -93,13 +84,13 @@ enable_force_move: true
 #*# [bed_mesh cold]
 #*# version = 1
 #*# points =
-#*# 	0.055000, 0.070000, 0.090000, 0.090000, 0.082500, 0.070000, 0.032500
-#*# 	0.005000, 0.007500, 0.020000, 0.020000, 0.017500, -0.007500, -0.040000
-#*# 	-0.017500, -0.022500, -0.007500, -0.005000, -0.012500, -0.032500, -0.057500
-#*# 	-0.012500, -0.015000, -0.005000, 0.000000, 0.005000, -0.020000, -0.052500
-#*# 	0.017500, 0.007500, 0.025000, 0.030000, 0.027500, 0.007500, -0.022500
-#*# 	0.072500, 0.050000, 0.065000, 0.072500, 0.080000, 0.060000, 0.027500
-#*# 	0.020000, 0.007500, 0.010000, 0.032500, 0.037500, 0.025000, -0.010000
+#*# 	0.037500, 0.062500, 0.087500, 0.087500, 0.085000, 0.065000, 0.015000
+#*# 	-0.020000, -0.007500, 0.015000, 0.017500, 0.012500, -0.017500, -0.065000
+#*# 	-0.042500, -0.035000, -0.012500, -0.007500, -0.015000, -0.045000, -0.087500
+#*# 	-0.037500, -0.027500, -0.007500, 0.000000, 0.002500, -0.032500, -0.080000
+#*# 	-0.007500, -0.002500, 0.022500, 0.040000, 0.027500, 0.005000, -0.047500
+#*# 	0.050000, 0.045000, 0.070000, 0.082500, 0.087500, 0.057500, 0.005000
+#*# 	0.000000, 0.010000, 0.022500, 0.050000, 0.055000, 0.030000, -0.025000
 #*# tension = 0.2
 #*# min_x = 30.0
 #*# algo = bicubic
@@ -114,13 +105,13 @@ enable_force_move: true
 #*# [bed_mesh abs]
 #*# version = 1
 #*# points =
-#*# 	  0.105000, 0.102500, 0.117500, 0.110000, 0.105000, 0.100000, 0.082500
-#*# 	  0.045000, 0.030000, 0.035000, 0.027500, 0.027500, 0.017500, -0.000000
-#*# 	  0.015000, -0.007500, -0.000000, -0.002500, -0.005000, -0.012500, -0.027500
-#*# 	  0.022500, 0.000000, 0.005000, 0.000000, 0.007500, -0.007500, -0.017500
-#*# 	  0.055000, 0.025000, 0.030000, 0.032500, 0.035000, 0.032500, 0.025000
-#*# 	  0.117500, 0.080000, 0.080000, 0.085000, 0.097500, 0.090000, 0.077500
-#*# 	  0.082500, 0.052500, 0.040000, 0.055000, 0.065000, 0.067500, 0.062500
+#*# 	  0.127500, 0.122500, 0.135000, 0.132500, 0.132500, 0.132500, 0.115000
+#*# 	  0.062500, 0.042500, 0.047500, 0.045000, 0.045000, 0.037500, 0.022500
+#*# 	  0.025000, -0.000000, 0.007500, 0.007500, -0.002500, -0.012500, -0.025000
+#*# 	  0.020000, -0.005000, 0.000000, 0.000000, 0.007500, -0.007500, -0.020000
+#*# 	  0.050000, 0.025000, 0.030000, 0.035000, 0.035000, 0.022500, 0.012500
+#*# 	  0.112500, 0.077500, 0.085000, 0.092500, 0.100000, 0.090000, 0.072500
+#*# 	  0.087500, 0.062500, 0.055000, 0.077500, 0.087500, 0.080000, 0.067500
 #*# tension = 0.2
 #*# min_x = 30.0
 #*# algo = bicubic

smartplug-shutdown.service

@@ -0,0 +1 @@
+/etc/systemd/system/smartplug-shutdown.service