tcl/target: add basic RP2040 target config

The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.

To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.

Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>

tcl/target/rp2040-core0.cfg

@@ -1,5 +1,17 @@
 # SPDX-License-Identifier: GPL-2.0-or-later
 
+# RP2040 is a microcontroller with dual Cortex-M0+ core.
+# https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html
+
+# The device requires multidrop SWD for debug.
+# This configuration file is intended for a special adapter
+# which selects a multidrop target on its own.
+# Cannot be used with a standard SWD adapter!
+
+echo "Warn : rp2040-core0.cfg configuration file is deprecated and will be"
+echo "       removed in the next release. Use following parameters instead:"
+echo "          -c 'set USE_CORE 0' -f target/rp2040.cfg"
+
 transport select swd
 
 source [find target/swj-dp.tcl]

tcl/target/rp2040.cfg

@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# RP2040 is a microcontroller with dual Cortex-M0+ core.
+# https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html
+
+# The device requires multidrop SWD for debug.
+transport select swd
+
+source [find target/swj-dp.tcl]
+
+if { [info exists CHIPNAME] } {
+	set _CHIPNAME $CHIPNAME
+} else {
+	set _CHIPNAME rp2040
+}
+
+if { [info exists WORKAREASIZE] } {
+	set _WORKAREASIZE $WORKAREASIZE
+} else {
+	set _WORKAREASIZE 0x10000
+}
+
+if { [info exists CPUTAPID] } {
+	set _CPUTAPID $CPUTAPID
+} else {
+	set _CPUTAPID 0x01002927
+}
+
+# Set to '0' or '1' for single core configuration,
+# anything else for isolated debugging of both cores
+if { [info exists USE_CORE] } {
+	set _USE_CORE $USE_CORE
+} else {
+	set _USE_CORE { 0 1 }
+}
+set _BOTH_CORES [expr { $_USE_CORE != 0 && $_USE_CORE != 1 }]
+
+swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
+
+# core 0
+if { $_USE_CORE != 1 } {
+	dap create $_CHIPNAME.dap0 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 0
+	set _TARGETNAME_0 $_CHIPNAME.core0
+	target create $_TARGETNAME_0 cortex_m -dap $_CHIPNAME.dap0 -coreid 0
+	# srst does not exist; use SYSRESETREQ to perform a soft reset
+	$_TARGETNAME_0 cortex_m reset_config sysresetreq
+}
+
+# core 1
+if { $_USE_CORE != 0 } {
+	dap create $_CHIPNAME.dap1 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 1
+	set _TARGETNAME_1 $_CHIPNAME.core1
+	target create $_TARGETNAME_1 cortex_m -dap $_CHIPNAME.dap1 -coreid 1
+	$_TARGETNAME_1 cortex_m reset_config sysresetreq
+}
+
+if { $_USE_CORE == 1 } {
+	set _FLASH_TARGET $_TARGETNAME_1
+} else {
+	set _FLASH_TARGET $_TARGETNAME_0
+}
+# Backup the work area. The flash probe runs an algorithm on the target CPU.
+# The flash is probed during gdb connect if gdb_memory_map is enabled (by default).
+$_FLASH_TARGET configure -work-area-phys 0x20010000 -work-area-size $_WORKAREASIZE -work-area-backup 1
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME rp2040_flash 0x10000000 0 0 0 $_FLASH_TARGET
+
+if { $_BOTH_CORES } {
+	# Alias to ensure gdb connecting to core 1 gets the correct memory map
+	flash bank $_CHIPNAME.alias virtual 0x10000000 0 0 0 $_TARGETNAME_1 $_FLASHNAME
+
+	# Select core 0
+	targets $_TARGETNAME_0
+}