3.14 1.0.x mx6 sr docker #26

bfg2008 · 2018-03-17T09:01:24Z

No description provided.

commit f2940e2 upstream. When calculating the required size of an RC QP send queue, leave enough space for masked atomic operations, which require more space than "regular" atomic operation. Fixes: 6fa8f71 ("IB/mlx4: Add support for masked atomic operations") Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4946784 upstream. When the volume resize operation shrinks a volume, LEBs will be unmapped. Since unmapping will not erase these LEBs immediately we have to wait for that operation to finish. Otherwise in case of a power cut right after writing the new volume table the UBI attach process can find more LEBs than the volume table knows. This will render the UBI image unattachable. Fix this issue by waiting for erase to complete and write the new volume table afterward. Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 714fb87 upstream. Install the UBI device object before we arm sysfs. Otherwise udev tries to read sysfs attributes before UBI is ready and udev rules will not match. Signed-off-by: Iosif Harutyunov <iharutyunov@sonicwall.com> [rw: massaged commit message] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 064cdd2 upstream. This patch fixes a race in iscsit_release_commands_from_conn() -> iscsit_free_cmd() -> transport_generic_free_cmd() + wait_for_tasks=1, where CMD_T_FABRIC_STOP could end up being set after the final kref_put() is called from core_tmr_abort_task() context. This results in transport_generic_free_cmd() blocking indefinately on se_cmd->cmd_wait_comp, because the target_release_cmd_kref() check for CMD_T_FABRIC_STOP returns false. To address this bug, make iscsit_release_commands_from_conn() do list_splice and set CMD_T_FABRIC_STOP early while holding iscsi_conn->cmd_lock. Also make iscsit_aborted_task() only remove iscsi_cmd_t if CMD_T_FABRIC_STOP has not already been set. Finally in target_release_cmd_kref(), only honor fabric_stop if CMD_T_ABORTED has been set. Cc: Mike Christie <mchristi@redhat.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Tested-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ea263c7 upstream. max_discard_sectors only 32bits, and some non scsi backend devices will set this to the max 0xffffffff, so we can end up overflowing during the max_unmap_lba_count calculation. This fixes a regression caused by my patch: commit 8a9ebe7 Author: Mike Christie <mchristi@redhat.com> Date: Mon Jan 18 14:09:27 2016 -0600 target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors which can result in extra discards being sent to due the overflow causing max_unmap_lba_count to be smaller than what the backing device can actually support. Signed-off-by: Mike Christie <mchristi@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9ac0108 upstream. Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have the same quirk for the Bus Reset. Fixes: c3e59ee ("PCI: Mark Atheros AR93xx to avoid bus reset") Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 99f3c90 upstream. When the corrupt_bio_byte feature was introduced it caused READ bios to no longer be errored with -EIO during the down_interval. This had to do with the complexity of needing to submit READs if the corrupt_bio_byte feature was used. Fix it so READ bios are properly errored with -EIO; doing so early in flakey_map() as long as there isn't a match for the corrupt_bio_byte feature. Fixes: a399879 ("dm flakey: add corrupt_bio_byte feature") Reported-by: Akira Hayakawa <ruby.wktk@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bca014c upstream. Signing a module should only make it trusted by the specific kernel it was built for, not anything else. Loading a signed module meant for a kernel with a different ABI could have interesting effects. Therefore, treat all signatures as invalid when a module is force-loaded. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…ng a key commit b8612e5 upstream. Signing a module should only make it trusted by the specific kernel it was built for, not anything else. If a module signing key is used for multiple ABI-incompatible kernels, the modules need to include enough version information to distinguish them. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5cf0791 upstream. There's a subtle preemption race on UP kernels: Usually current->mm (and therefore mm->pgd) stays the same during the lifetime of a task so it does not matter if a task gets preempted during the read and write of the CR3. But then, there is this scenario on x86-UP: TaskA is in do_exit() and exit_mm() sets current->mm = NULL followed by: -> mmput() -> exit_mmap() -> tlb_finish_mmu() -> tlb_flush_mmu() -> tlb_flush_mmu_tlbonly() -> tlb_flush() -> flush_tlb_mm_range() -> __flush_tlb_up() -> __flush_tlb() -> __native_flush_tlb() At this point current->mm is NULL but current->active_mm still points to the "old" mm. Let's preempt taskA _after_ native_read_cr3() by taskB. TaskB has its own mm so CR3 has changed. Now preempt back to taskA. TaskA has no ->mm set so it borrows taskB's mm and so CR3 remains unchanged. Once taskA gets active it continues where it was interrupted and that means it writes its old CR3 value back. Everything is fine because userland won't need its memory anymore. Now the fun part: Let's preempt taskA one more time and get back to taskB. This time switch_mm() won't do a thing because oldmm (->active_mm) is the same as mm (as per context_switch()). So we remain with a bad CR3 / PGD and return to userland. The next thing that happens is handle_mm_fault() with an address for the execution of its code in userland. handle_mm_fault() realizes that it has a PTE with proper rights so it returns doing nothing. But the CPU looks at the wrong PGD and insists that something is wrong and faults again. And again. And one more time… This pagefault circle continues until the scheduler gets tired of it and puts another task on the CPU. It gets little difficult if the task is a RT task with a high priority. The system will either freeze or it gets fixed by the software watchdog thread which usually runs at RT-max prio. But waiting for the watchdog will increase the latency of the RT task which is no good. Fix this by disabling preemption across the critical code section. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mel Gorman <mgorman@suse.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/1470404259-26290-1-git-send-email-bigeasy@linutronix.de [ Prettified the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3146bc6 upstream. AT_VECTOR_SIZE_ARCH should be defined with the maximum number of NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined for arm64 at all even though ARCH_DLINFO will contain one NEW_AUX_ENT for the VDSO address. This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for AT_BASE_PLATFORM which arm64 doesn't use, but lets define it now and add the comment above ARCH_DLINFO as found in several other architectures to remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to date. Fixes: f668cd1 ("arm64: ELF definitions") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3eb53b2 upstream. When building gccgo in userspace, errno.h gets parsed and the go include file sysinfo.go is generated. Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED is defined later on in errno.h, this leads to go complaining that EREFUSED isn't defined yet. Fix this trivial problem by moving the define of EREFUSED down after ECONNREFUSED in errno.h (and clean up the indenting while touching this line). Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c20aecf upstream. If a device quirk modifies the pci_dev->cfg_size to be less than PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256), the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE. Allow sysfs access to config space up to cfg_size, even if the device doesn't support the entire 4096-byte PCIe config space. Note that pci_read_config() and pci_write_config() limit access to dev->cfg_size even though pcie_config_attr contains 4096 (the maximum size). Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com> [simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com> [bhelgaas: more changelog edits] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a755e16 upstream. Device IDs for the Netronome NFP3200, NFP3240, NFP6000, and NFP6000 SR-IOV devices. Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com> [simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9f33a2a upstream. The NFP6000 has an erratum where reading/writing to PCI config space addresses above 0x600 can cause the NFP to generate PCIe completion timeouts. Limit the NFP6000's config space size to 0x600 bytes. Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com> [simon: edited changelog] Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 69874ec upstream. Add the device ID for the PF of the NFP4000. The device ID for the VF, 0x6003, is already present as PCI_DEVICE_ID_NETRONOME_NFP6000_VF. Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c2e771b upstream. Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI config space addresses above 0x600 can cause the NFP to generate PCIe completion timeouts. Limit the NFP4000's PF's config space size to 0x600 bytes as is already done for the NFP6000. The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same device ID as the NFP6000's VF. Thus, its config space is already limited by the existing use of quirk_nfp6000(). Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c7de573 upstream. When using SG lists, we would end up setting request->actual to: num_mapped_sgs * (request->length - count) Let's fix that up by incrementing request->actual only once. Reported-by: Brian E Rogers <brian.e.rogers@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8a1b272 upstream. Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can handle the new speed. In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed devices. In a few places we add a "Plus" string to inform the user of the new speed. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aed9d65 upstream. Erroneous or malicious endpoint descriptors may have non-zero bits in reserved positions, or out-of-bounds values. This patch helps prevent these from causing problems by bounds-checking the wMaxPacketValue entries in endpoint descriptors and capping the values at the maximum allowed. This issue was first discovered and tests were conducted by Jake Lamberson <jake.lamberson1@gmail.com>, an intern working for Rosie Hall. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: roswest <roswest@cisco.com> Tested-by: roswest <roswest@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 88716a9 upstream. After a device is disconnected, xhci_stop_device() will be invoked in xhci_bus_suspend(). Also the "disconnect" IRQ will have ISR to invoke xhci_free_virt_device() in this sequence. xhci_irq -> xhci_handle_event -> handle_cmd_completion -> xhci_handle_cmd_disable_slot -> xhci_free_virt_device If xhci->devs[slot_id] has been assigned to NULL in xhci_free_virt_device(), then virt_dev->eps[i].ring in xhci_stop_device() may point to an invlid address to cause kernel panic. virt_dev = xhci->devs[slot_id]; : if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue) [] Unable to handle kernel paging request at virtual address 00001a68 [] pgd=ffffffc001430000 [] [00001a68] *pgd=000000013c807003, *pud=000000013c807003, *pmd=000000013c808003, *pte=0000000000000000 [] Internal error: Oops: 96000006 [#1] PREEMPT SMP [] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U [] Workqueue: pm pm_runtime_work [] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti: ffffffc0bc0ec000 [] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4 This issue is found when running with realtek ethernet device (0bda:8153). Signed-off-by: Jim Lin <jilin@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 647024a upstream. udriver struct allocated by kzalloc() will not be freed if usb_register() and next calls fail. This patch fixes this by adding one more step with kfree(udriver) in error path. Signed-off-by: Alexey Klimov <klimov.linux@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cf1b180 upstream. The device has four interfaces; the three serial ports ought to be handled by this driver: 00 Diagnostic interface serial port 01 NMEA device serial port 02 Mass storage (sd card) 03 Modem serial port The other product ids listed in the Windows driver are present already. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 01d7956 upstream. This patch adds a set of compositions for Telit LE920A4. Compositions in short are: 0x1207: tty + tty 0x1208: tty + adb + tty + tty 0x1211: tty + adb + ecm 0x1212: tty + adb 0x1213: ecm + tty 0x1214: tty + adb + ecm + tty telit_le922_blacklist_usbcfg3 is reused for compositions 0x1211 and 0x1214 due to the same interfaces positions. Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ae34d12 upstream. BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0 UART/FIFO IC. To support BCM920706V2_EVAL dev board for WICED development on Linux. Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading ftdi_sio for this board. Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6977495 upstream. Ivium Technologies uses the FTDI VID with custom PIDs for their line of electrochemical interfaces and the PalmSens they developed for PalmSens BV. Signed-off-by: Robert Delien <robert@delien.nl> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0caf6b3 upstream. In most cases the devices with the speed set to USB_SPEED_SUPER_PLUS are handled like regular SuperSpeed devices. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 993f88f upstream. Fix typo in edac_inc_ue_error() to increment ue_noinfo_count instead of ce_noinfo_count. Signed-off-by: Emmanouil Maroudas <emmanouil.maroudas@gmail.com> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Fixes: 4275be6 ("edac: Change internal representation to work with layers") Link: http://lkml.kernel.org/r/1461425580-5898-1-git-send-email-emmanouil.maroudas@gmail.com Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9ba333d upstream. When a device is in a status where CIO has killed all I/O by itself the interrupt for a clear request may not contain an irb to determine the clear function. Instead it contains an error pointer -EIO. This was ignored by the DASD int_handler leading to a hanging device waiting for a clear interrupt. Handle -EIO error pointer correctly for requests that are clear pending and treat the clear as successful. Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com> Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 45caeaa ] As Eric Dumazet pointed out this also needs to be fixed in IPv6. v2: Contains the IPv6 tcp/Ipv6 dccp patches as well. We have seen a few incidents lately where a dst_enty has been freed with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that dst_entry. If the conditions/timings are right a crash then ensues when the freed dst_entry is referenced later on. A Common crashing back trace is: Freescale#8 [] page_fault at ffffffff8163e648 [exception RIP: __tcp_ack_snd_check+74] . . Freescale#9 [] tcp_rcv_established at ffffffff81580b64 Freescale#10 [] tcp_v4_do_rcv at ffffffff8158b54a Freescale#11 [] tcp_v4_rcv at ffffffff8158cd02 Freescale#12 [] ip_local_deliver_finish at ffffffff815668f4 Freescale#13 [] ip_local_deliver at ffffffff81566bd9 Freescale#14 [] ip_rcv_finish at ffffffff8156656d Freescale#15 [] ip_rcv at ffffffff81566f06 Freescale#16 [] __netif_receive_skb_core at ffffffff8152b3a2 Freescale#17 [] __netif_receive_skb at ffffffff8152b608 Freescale#18 [] netif_receive_skb at ffffffff8152b690 Freescale#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3] Freescale#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3] Freescale#21 [] net_rx_action at ffffffff8152bac2 Freescale#22 [] __do_softirq at ffffffff81084b4f Freescale#23 [] call_softirq at ffffffff8164845c Freescale#24 [] do_softirq at ffffffff81016fc5 Freescale#25 [] irq_exit at ffffffff81084ee5 Freescale#26 [] do_IRQ at ffffffff81648ff8 Of course it may happen with other NIC drivers as well. It's found the freed dst_entry here: 224 static bool tcp_in_quickack_mode(struct sock *sk)↩ 225 {↩ 226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩ 227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩ 228 ↩ 229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩ 230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩ 231 }↩ But there are other backtraces attributed to the same freed dst_entry in netfilter code as well. All the vmcores showed 2 significant clues: - Remote hosts behind the default gateway had always been redirected to a different gateway. A rtable/dst_entry will be added for that host. Making more dst_entrys with lower reference counts. Making this more probable. - All vmcores showed a postitive LockDroppedIcmps value, e.g: LockDroppedIcmps 267 A closer look at the tcp_v4_err() handler revealed that do_redirect() will run regardless of whether user space has the socket locked. This can result in a race condition where the same dst_entry cached in sk->sk_dst_entry can be decremented twice for the same socket via: do_redirect()->__sk_dst_check()-> dst_release(). Which leads to the dst_entry being prematurely freed with another socket pointing to it via sk->sk_dst_cache and a subsequent crash. To fix this skip do_redirect() if usespace has the socket locked. Instead let the redirect take place later when user space does not have the socket locked. The dccp/IPv6 code is very similar in this respect, so fixing it there too. As Eric Garver pointed out the following commit now invalidates routes. Which can set the dst->obsolete flag so that ipv4_dst_check() returns null and triggers the dst_release(). Fixes: ceb3320 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <egarver@redhat.com> Cc: Hannes Sowa <hsowa@redhat.com> Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c37c287 ] Reported by syzkaller: *** Guest State *** CR0: actual=0x0000000080010031, shadow=0x0000000060000010, gh_mask=fffffffffffffff7 CR4: actual=0x0000000000002061, shadow=0x0000000000000000, gh_mask=ffffffffffffe8f1 CR3 = 0x000000002081e000 RSP = 0x000000000000fffa RIP = 0x0000000000000000 RFLAGS=0x00023000 DR7 = 0x00000000000000 ^^^^^^^^^^ ------------[ cut here ]------------ WARNING: CPU: 6 PID: 24431 at /home/kernel/linux/arch/x86/kvm//x86.c:7302 kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm] CPU: 6 PID: 24431 Comm: reprotest Tainted: G W OE 4.14.0+ #26 RIP: 0010:kvm_arch_vcpu_ioctl_run+0x651/0x2ea0 [kvm] RSP: 0018:ffff880291d179e0 EFLAGS: 00010202 Call Trace: kvm_vcpu_ioctl+0x479/0x880 [kvm] do_vfs_ioctl+0x142/0x9a0 SyS_ioctl+0x74/0x80 entry_SYSCALL_64_fastpath+0x23/0x9a The failed vmentry is triggered by the following beautified testcase: #include <unistd.h> #include <sys/syscall.h> #include <string.h> #include <stdint.h> #include <linux/kvm.h> #include <fcntl.h> #include <sys/ioctl.h> long r[5]; int main() { struct kvm_debugregs dr = { 0 }; r[2] = open("/dev/kvm", O_RDONLY); r[3] = ioctl(r[2], KVM_CREATE_VM, 0); r[4] = ioctl(r[3], KVM_CREATE_VCPU, 7); struct kvm_guest_debug debug = { .control = 0xf0403, .arch = { .debugreg[6] = 0x2, .debugreg[7] = 0x2 } }; ioctl(r[4], KVM_SET_GUEST_DEBUG, &debug); ioctl(r[4], KVM_RUN, 0); } which testcase tries to setup the processor specific debug registers and configure vCPU for handling guest debug events through KVM_SET_GUEST_DEBUG. The KVM_SET_GUEST_DEBUG ioctl will get and set rflags in order to set TF bit if single step is needed. All regs' caches are reset to avail and GUEST_RFLAGS vmcs field is reset to 0x2 during vCPU reset. However, the cache of rflags is not reset during vCPU reset. The function vmx_get_rflags() returns an unreset rflags cache value since the cache is marked avail, it is 0 after boot. Vmentry fails if the rflags reserved bit 1 is 0. This patch fixes it by resetting both the GUEST_RFLAGS vmcs field and its cache to 0x2 during vCPU reset. Reported-by: Dmitry Vyukov <dvyukov@google.com> Tested-by: Dmitry Vyukov <dvyukov@google.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>

[ Upstream commit e24c644 ] I compiled with AddressSanitizer and I had these memory leaks while I was using the tep_parse_format function: Direct leak of 28 byte(s) in 4 object(s) allocated from: #0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe) Freescale#1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985 Freescale#2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140 Freescale#3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206 Freescale#4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291 Freescale#5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299 Freescale#6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849 Freescale#7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161 Freescale#8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207 Freescale#9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786 Freescale#10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285 Freescale#11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369 Freescale#12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335 Freescale#13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389 Freescale#14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431 Freescale#15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251 Freescale#16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284 Freescale#17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593 Freescale#18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727 Freescale#19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048 Freescale#20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127 Freescale#21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152 Freescale#22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252 Freescale#23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347 Freescale#24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461 Freescale#25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673 Freescale#26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2) The token variable in the process_dynamic_array_len function is allocated in the read_expect_type function, but is not freed before calling the read_token function. Free the token variable before calling read_token in order to plug the leak. Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Link: https://lore.kernel.org/linux-trace-devel/20200730150236.5392-1-pduplessis@efficios.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 96ecdcc ] Netpoll can try to poll napi as soon as napi_enable() is called. It crashes trying to access a doorbell which is still NULL: BUG: kernel NULL pointer dereference, address: 0000000000000000 CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty Freescale#26 RIP: 0010:bnxt_poll+0x121/0x1c0 Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02 41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a netpoll_poll_dev+0xbd/0x1a0 __netpoll_send_skb+0x1b2/0x210 netpoll_send_udp+0x2c9/0x406 write_ext_msg+0x1d7/0x1f0 console_unlock+0x23c/0x520 vprintk_emit+0xe0/0x1d0 printk+0x58/0x6f x86_vector_activate.cold+0xf/0x46 __irq_domain_activate_irq+0x50/0x80 __irq_domain_activate_irq+0x32/0x80 __irq_domain_activate_irq+0x32/0x80 irq_domain_activate_irq+0x25/0x40 __setup_irq+0x2d2/0x700 request_threaded_irq+0xfb/0x160 __bnxt_open_nic+0x3b1/0x750 bnxt_open_nic+0x19/0x30 ethtool_set_channels+0x1ac/0x220 dev_ethtool+0x11ba/0x2240 dev_ioctl+0x1cf/0x390 sock_do_ioctl+0x95/0x130 Reported-by: Rob Sherwood <rsher@fb.com> Fixes: c0c050c ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 96298f6 ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 Freescale#32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by: Howard Chung <howardchung@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 24201a6 ] The DMA error handler routine is currently a tasklet, scheduled to run after the DMA error IRQ was handled. However it needs to take the MDIO mutex, which is not allowed to do in a tasklet. A kernel (with debug options) complains consequently: [ 614.050361] net eth0: DMA Tx error 0x174019 [ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce [ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935 [ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4 [ 614.135428] 3 locks held by kworker/u4:4/40: [ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8 [ 614.177528] Freescale#1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8 [ 614.209033] Freescale#2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58 [ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 Freescale#26 [ 614.260854] Hardware name: ARM Test FPGA (DT) [ 614.274734] Workqueue: rpciod rpc_async_schedule [ 614.289022] Call trace: [ 614.296871] dump_backtrace+0x0/0x1a0 [ 614.308311] show_stack+0x14/0x20 [ 614.318751] dump_stack+0xbc/0x100 [ 614.329403] ___might_sleep+0xf0/0x140 [ 614.341018] __might_sleep+0x4c/0x80 [ 614.352201] __mutex_lock+0x5c/0x8a8 [ 614.363348] mutex_lock_nested+0x1c/0x28 [ 614.375654] axienet_dma_err_handler+0x38/0x388 [ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8 [ 614.405894] tasklet_action+0x24/0x30 [ 614.417297] efi_header_end+0xe0/0x494 [ 614.429020] irq_exit+0xd0/0xd8 [ 614.439047] __handle_domain_irq+0x60/0xb0 [ 614.451877] gic_handle_irq+0xdc/0x2d0 [ 614.463486] el1_irq+0xcc/0x180 [ 614.473451] __tcp_transmit_skb+0x41c/0xb58 [ 614.486513] tcp_write_xmit+0x224/0x10a0 [ 614.498792] __tcp_push_pending_frames+0x38/0xc8 [ 614.513126] tcp_rcv_established+0x41c/0x820 [ 614.526301] tcp_v4_do_rcv+0x8c/0x218 [ 614.537784] __release_sock+0x5c/0x108 [ 614.549466] release_sock+0x34/0xa0 [ 614.560318] tcp_sendmsg+0x40/0x58 [ 614.571053] inet_sendmsg+0x40/0x68 [ 614.582061] sock_sendmsg+0x18/0x30 [ 614.593074] xs_sendpages+0x218/0x328 [ 614.604506] xs_tcp_send_request+0xa0/0x1b8 [ 614.617461] xprt_transmit+0xc8/0x4f0 [ 614.628943] call_transmit+0x8c/0xa0 [ 614.640028] __rpc_execute+0xbc/0x6f8 [ 614.651380] rpc_async_schedule+0x28/0x48 [ 614.663846] process_one_work+0x298/0x6a8 [ 614.676299] worker_thread+0x40/0x490 [ 614.687687] kthread+0x134/0x138 [ 614.697804] ret_from_fork+0x10/0x18 [ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down [ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off Since tasklets are not really popular anymore anyway, lets convert this over to a work queue, which can sleep and thus can take the MDIO mutex. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e24c644 ] I compiled with AddressSanitizer and I had these memory leaks while I was using the tep_parse_format function: Direct leak of 28 byte(s) in 4 object(s) allocated from: #0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe) Freescale#1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985 Freescale#2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140 Freescale#3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206 Freescale#4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291 Freescale#5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299 Freescale#6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849 Freescale#7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161 Freescale#8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207 Freescale#9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786 Freescale#10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285 Freescale#11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369 Freescale#12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335 Freescale#13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389 Freescale#14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431 Freescale#15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251 Freescale#16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284 Freescale#17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593 Freescale#18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727 Freescale#19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048 Freescale#20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127 Freescale#21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152 Freescale#22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252 Freescale#23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347 Freescale#24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461 Freescale#25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673 Freescale#26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2) The token variable in the process_dynamic_array_len function is allocated in the read_expect_type function, but is not freed before calling the read_token function. Free the token variable before calling read_token in order to plug the leak. Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Link: https://lore.kernel.org/linux-trace-devel/20200730150236.5392-1-pduplessis@efficios.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 96ecdcc upstream. Netpoll can try to poll napi as soon as napi_enable() is called. It crashes trying to access a doorbell which is still NULL: BUG: kernel NULL pointer dereference, address: 0000000000000000 CPU: 59 PID: 6039 Comm: ethtool Kdump: loaded Tainted: G S 5.9.0-rc1-00469-g5fd99b5d9950-dirty Freescale#26 RIP: 0010:bnxt_poll+0x121/0x1c0 Code: c4 20 44 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 41 8b 86 a0 01 00 00 41 23 85 18 01 00 00 49 8b 96 a8 01 00 00 0d 00 00 00 24 <89> 02 41 f6 45 77 02 74 cb 49 8b ae d8 01 00 00 31 c0 c7 44 24 1a netpoll_poll_dev+0xbd/0x1a0 __netpoll_send_skb+0x1b2/0x210 netpoll_send_udp+0x2c9/0x406 write_ext_msg+0x1d7/0x1f0 console_unlock+0x23c/0x520 vprintk_emit+0xe0/0x1d0 printk+0x58/0x6f x86_vector_activate.cold+0xf/0x46 __irq_domain_activate_irq+0x50/0x80 __irq_domain_activate_irq+0x32/0x80 __irq_domain_activate_irq+0x32/0x80 irq_domain_activate_irq+0x25/0x40 __setup_irq+0x2d2/0x700 request_threaded_irq+0xfb/0x160 __bnxt_open_nic+0x3b1/0x750 bnxt_open_nic+0x19/0x30 ethtool_set_channels+0x1ac/0x220 dev_ethtool+0x11ba/0x2240 dev_ioctl+0x1cf/0x390 sock_do_ioctl+0x95/0x130 Reported-by: Rob Sherwood <rsher@fb.com> Fixes: c0c050c ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 96298f6 ] According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5, the incoming L2CAP_ConfigReq should be handled during OPEN state. The section below shows the btmon trace when running L2CAP/COS/CFD/BV-12-C before and after this change. === Before === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ...... < ACL Data TX: Handle 256 flags 0x00 dlen 14 Freescale#32 L2CAP: Command Reject (0x01) ident 3 len 6 Reason: Invalid CID in request (0x0002) Destination CID: 64 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#33 Num handles: 1 Handle: 256 Count: 1 ... === After === ... > ACL Data RX: Handle 256 flags 0x02 dlen 12 Freescale#22 L2CAP: Connection Request (0x02) ident 2 len 4 PSM: 1 (0x0001) Source CID: 65 < ACL Data TX: Handle 256 flags 0x00 dlen 16 Freescale#23 L2CAP: Connection Response (0x03) ident 2 len 8 Destination CID: 64 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#24 L2CAP: Configure Request (0x04) ident 2 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#25 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#26 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 16 Freescale#27 L2CAP: Configure Request (0x04) ident 3 len 8 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 .. < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#28 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#29 Num handles: 1 Handle: 256 Count: 1 > ACL Data RX: Handle 256 flags 0x02 dlen 14 Freescale#30 L2CAP: Configure Response (0x05) ident 2 len 6 Source CID: 64 Flags: 0x0000 Result: Success (0x0000) > ACL Data RX: Handle 256 flags 0x02 dlen 20 Freescale#31 L2CAP: Configure Request (0x04) ident 3 len 12 Destination CID: 64 Flags: 0x0000 Option: Unknown (0x10) [hint] 01 00 91 02 11 11 ..... < ACL Data TX: Handle 256 flags 0x00 dlen 18 Freescale#32 L2CAP: Configure Response (0x05) ident 3 len 10 Source CID: 65 Flags: 0x0000 Result: Success (0x0000) Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 672 < ACL Data TX: Handle 256 flags 0x00 dlen 12 Freescale#33 L2CAP: Configure Request (0x04) ident 3 len 4 Destination CID: 65 Flags: 0x0000 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#34 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 Freescale#35 Num handles: 1 Handle: 256 Count: 1 ... Signed-off-by: Howard Chung <howardchung@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9d23246 ] This patch fixes issues which occurs when dlm lowcomms synchronize their workqueues but dlm application layer already released the lockspace. In such cases messages like: dlm: gfs2: release_lockspace final free dlm: invalid lockspace 3841231384 from 1 cmd 1 type 11 are printed on the kernel log. This patch is solving this issue by introducing a new "shutdown" hook before calling "stop" hook when the lockspace is going to be released finally. This should pretend any dlm messages sitting in the workqueues during or after lockspace removal. It's necessary to call dlm_scand_stop() as I instrumented dlm_lowcomms_get_buffer() code to report a warning after it's called after dlm_midcomms_shutdown() functionality, see below: WARNING: CPU: 1 PID: 3794 at fs/dlm/midcomms.c:1003 dlm_midcomms_get_buffer+0x167/0x180 Modules linked in: joydev iTCO_wdt intel_pmc_bxt iTCO_vendor_support drm_ttm_helper ttm pcspkr serio_raw i2c_i801 i2c_smbus drm_kms_helper virtio_scsi lpc_ich virtio_balloon virtio_console xhci_pci xhci_pci_renesas cec qemu_fw_cfg drm [last unloaded: qxl] CPU: 1 PID: 3794 Comm: dlm_scand Tainted: G W 5.11.0+ Freescale#26 Hardware name: Red Hat KVM/RHEL-AV, BIOS 1.13.0-2.module+el8.3.0+7353+9de0a3cc 04/01/2014 RIP: 0010:dlm_midcomms_get_buffer+0x167/0x180 Code: 5d 41 5c 41 5d 41 5e 41 5f c3 0f 0b 45 31 e4 5b 5d 4c 89 e0 41 5c 41 5d 41 5e 41 5f c3 4c 89 e7 45 31 e4 e8 3b f1 ec ff eb 86 <0f> 0b 4c 89 e7 45 31 e4 e8 2c f1 ec ff e9 74 ff ff ff 0f 1f 80 00 RSP: 0018:ffffa81503f8fe60 EFLAGS: 00010202 RAX: 0000000000000008 RBX: ffff8f969827f200 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffffffffad1e89a0 RDI: ffff8f96a5294160 RBP: 0000000000000001 R08: 0000000000000000 R09: ffff8f96a250bc60 R10: 00000000000045d3 R11: 0000000000000000 R12: ffff8f96a250bc60 R13: ffffa81503f8fec8 R14: 0000000000000070 R15: 0000000000000c40 FS: 0000000000000000(0000) GS:ffff8f96fbc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055aa3351c000 CR3: 000000010bf22000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: dlm_scan_rsbs+0x420/0x670 ? dlm_uevent+0x20/0x20 dlm_scand+0xbf/0xe0 kthread+0x13a/0x150 ? __kthread_bind_mask+0x60/0x60 ret_from_fork+0x22/0x30 To synchronize all dlm scand messages we stop it right before shutdown hook. Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d5027ca ] Ritesh reported a bug [1] against UML, noting that it crashed on startup. The backtrace shows the following (heavily redacted): (gdb) bt ... Freescale#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268 Freescale#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2 Freescale#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72 ... Freescale#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359 ... Freescale#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486 Freescale#45 0x00007f8990968b85 in __getgrnam_r [...] Freescale#46 0x00007f89909d6b77 in grantpt [...] Freescale#47 0x00007f8990a9394e in __GI_openpty [...] Freescale#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407 Freescale#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598 Freescale#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45 Freescale#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334 Freescale#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144 indicating that the UML function openpty_cb() calls openpty(), which internally calls __getgrnam_r(), which causes the nsswitch machinery to get started. This loads, through lots of indirection that I snipped, the libcom_err.so.2 library, which (in an unknown function, "??") calls sem_init(). Now, of course it wants to get libpthread's sem_init(), since it's linked against libpthread. However, the dynamic linker looks up that symbol against the binary first, and gets the kernel's sem_init(). Hajime Tazaki noted that "objcopy -L" can localize a symbol, so the dynamic linker wouldn't do the lookup this way. I tried, but for some reason that didn't seem to work. Doing the same thing in the linker script instead does seem to work, though I cannot entirely explain - it *also* works if I just add "VERSION { { global: *; }; }" instead, indicating that something else is happening that I don't really understand. It may be that explicitly doing that marks them with some kind of empty version, and that's different from the default. Explicitly marking them with a version breaks kallsyms, so that doesn't seem to be possible. Marking all the symbols as local seems correct, and does seem to address the issue, so do that. Also do it for static link, nsswitch libraries could still be loaded there. [1] https://bugs.debian.org/983379 Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6c881ca ] To quote Alexey[1]: I was adding custom tracepoint to the kernel, grabbed full F34 kernel .config, disabled modules and booted whole shebang as VM kernel. Then did perf record -a -e ... It crashed: general protection fault, probably for non-canonical address 0x435f5346592e4243: 0000 [Freescale#1] SMP PTI CPU: 1 PID: 842 Comm: cat Not tainted 5.12.6+ Freescale#26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:t_show+0x22/0xd0 Then reproducer was narrowed to # cat /sys/kernel/tracing/printk_formats Original F34 kernel with modules didn't crash. So I started to disable options and after disabling AFS everything started working again. The root cause is that AFS was placing char arrays content into a section full of _pointers_ to strings with predictable consequences. Non canonical address 435f5346592e4243 is "CB.YFS_" which came from CM_NAME macro. Steps to reproduce: CONFIG_AFS=y CONFIG_TRACING=y # cat /sys/kernel/tracing/printk_formats Fix this by the following means: (1) Add enum->string translation tables in the event header with the AFS and YFS cache/callback manager operations listed by RPC operation ID. (2) Modify the afs_cb_call tracepoint to print the string from the translation table rather than using the string at the afs_call name pointer. (3) Switch translation table depending on the service we're being accessed as (AFS or YFS) in the tracepoint print clause. Will this cause problems to userspace utilities? Note that the symbolic representation of the YFS service ID isn't available to this header, so I've put it in as a number. I'm not sure if this is the best way to do this. (4) Remove the name wrangling (CM_NAME) macro and put the names directly into the afs_call_type structs in cmservice.c. Fixes: 8e8d7f1 ("afs: Add some tracepoints") Reported-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> cc: Andrew Morton <akpm@linux-foundation.org> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/YLAXfvZ+rObEOdc%2F@localhost.localdomain/ [1] Link: https://lore.kernel.org/r/643721.1623754699@warthog.procyon.org.uk/ Link: https://lore.kernel.org/r/162430903582.2896199.6098150063997983353.stgit@warthog.procyon.org.uk/ # v1 Link: https://lore.kernel.org/r/162609463957.3133237.15916579353149746363.stgit@warthog.procyon.org.uk/ # v1 (repost) Link: https://lore.kernel.org/r/162610726860.3408253.445207609466288531.stgit@warthog.procyon.org.uk/ # v2 Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d412137 ] The perf_buffer fails on system with offline cpus: # test_progs -t perf_buffer test_perf_buffer:PASS:nr_cpus 0 nsec test_perf_buffer:PASS:nr_on_cpus 0 nsec test_perf_buffer:PASS:skel_load 0 nsec test_perf_buffer:PASS:attach_kprobe 0 nsec test_perf_buffer:PASS:perf_buf__new 0 nsec test_perf_buffer:PASS:epoll_fd 0 nsec skipping offline CPU Freescale#24 skipping offline CPU Freescale#25 skipping offline CPU Freescale#26 skipping offline CPU Freescale#27 skipping offline CPU Freescale#28 skipping offline CPU Freescale#29 skipping offline CPU Freescale#30 skipping offline CPU Freescale#31 test_perf_buffer:PASS:perf_buffer__poll 0 nsec test_perf_buffer:PASS:seen_cpu_cnt 0 nsec test_perf_buffer:FAIL:buf_cnt got 24, expected 32 Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED Changing the test to check online cpus instead of possible. Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20211021114132.8196-2-jolsa@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d5027ca ] Ritesh reported a bug [1] against UML, noting that it crashed on startup. The backtrace shows the following (heavily redacted): (gdb) bt ... Freescale#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268 Freescale#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2 Freescale#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72 ... Freescale#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359 ... Freescale#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486 Freescale#45 0x00007f8990968b85 in __getgrnam_r [...] Freescale#46 0x00007f89909d6b77 in grantpt [...] Freescale#47 0x00007f8990a9394e in __GI_openpty [...] Freescale#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407 Freescale#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598 Freescale#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45 Freescale#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334 Freescale#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144 indicating that the UML function openpty_cb() calls openpty(), which internally calls __getgrnam_r(), which causes the nsswitch machinery to get started. This loads, through lots of indirection that I snipped, the libcom_err.so.2 library, which (in an unknown function, "??") calls sem_init(). Now, of course it wants to get libpthread's sem_init(), since it's linked against libpthread. However, the dynamic linker looks up that symbol against the binary first, and gets the kernel's sem_init(). Hajime Tazaki noted that "objcopy -L" can localize a symbol, so the dynamic linker wouldn't do the lookup this way. I tried, but for some reason that didn't seem to work. Doing the same thing in the linker script instead does seem to work, though I cannot entirely explain - it *also* works if I just add "VERSION { { global: *; }; }" instead, indicating that something else is happening that I don't really understand. It may be that explicitly doing that marks them with some kind of empty version, and that's different from the default. Explicitly marking them with a version breaks kallsyms, so that doesn't seem to be possible. Marking all the symbols as local seems correct, and does seem to address the issue, so do that. Also do it for static link, nsswitch libraries could still be loaded there. [1] https://bugs.debian.org/983379 Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit b7fb2da upstream. struct rpmsg_ctrldev contains a struct cdev. The current code frees the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the cdev is a managed object, therefore its release is not predictable and the rpmsg_ctrldev could be freed before the cdev is entirely released, as in the backtrace below. [ 93.625603] ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x7c [ 93.636115] WARNING: CPU: 0 PID: 12 at lib/debugobjects.c:488 debug_print_object+0x13c/0x1b0 [ 93.644799] Modules linked in: veth xt_cgroup xt_MASQUERADE rfcomm algif_hash algif_skcipher af_alg uinput ip6table_nat fuse uvcvideo videobuf2_vmalloc venus_enc venus_dec videobuf2_dma_contig hci_uart btandroid btqca snd_soc_rt5682_i2c bluetooth qcom_spmi_temp_alarm snd_soc_rt5682v [ 93.715175] CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: G B 5.4.163-lockdep Freescale#26 [ 93.723855] Hardware name: Google Lazor (rev3 - 8) with LTE (DT) [ 93.730055] Workqueue: events kobject_delayed_cleanup [ 93.735271] pstate: 60c00009 (nZCv daif +PAN +UAO) [ 93.740216] pc : debug_print_object+0x13c/0x1b0 [ 93.744890] lr : debug_print_object+0x13c/0x1b0 [ 93.749555] sp : ffffffacf5bc7940 [ 93.752978] x29: ffffffacf5bc7940 x28: dfffffd000000000 [ 93.758448] x27: ffffffacdb11a800 x26: dfffffd000000000 [ 93.763916] x25: ffffffd0734f856c x24: dfffffd000000000 [ 93.769389] x23: 0000000000000000 x22: ffffffd0733c35b0 [ 93.774860] x21: ffffffd0751994a0 x20: ffffffd075ec27c0 [ 93.780338] x19: ffffffd075199100 x18: 00000000000276e0 [ 93.785814] x17: 0000000000000000 x16: dfffffd000000000 [ 93.791291] x15: ffffffffffffffff x14: 6e6968207473696c [ 93.796768] x13: 0000000000000000 x12: ffffffd075e2b000 [ 93.802244] x11: 0000000000000001 x10: 0000000000000000 [ 93.807723] x9 : d13400dff1921900 x8 : d13400dff1921900 [ 93.813200] x7 : 0000000000000000 x6 : 0000000000000000 [ 93.818676] x5 : 0000000000000080 x4 : 0000000000000000 [ 93.824152] x3 : ffffffd0732a0fa4 x2 : 0000000000000001 [ 93.829628] x1 : ffffffacf5bc7580 x0 : 0000000000000061 [ 93.835104] Call trace: [ 93.837644] debug_print_object+0x13c/0x1b0 [ 93.841963] __debug_check_no_obj_freed+0x25c/0x3c0 [ 93.846987] debug_check_no_obj_freed+0x18/0x20 [ 93.851669] slab_free_freelist_hook+0xbc/0x1e4 [ 93.856346] kfree+0xfc/0x2f4 [ 93.859416] rpmsg_ctrldev_release_device+0x78/0xb8 [ 93.864445] device_release+0x84/0x168 [ 93.868310] kobject_cleanup+0x12c/0x298 [ 93.872356] kobject_delayed_cleanup+0x10/0x18 [ 93.876948] process_one_work+0x578/0x92c [ 93.881086] worker_thread+0x804/0xcf8 [ 93.884963] kthread+0x2a8/0x314 [ 93.888303] ret_from_fork+0x10/0x18 The cdev_device_add/del() API was created to address this issue (see commit '233ed09d7fda ("chardev: add helper function to register char devs with a struct device")'), use it instead of cdev add/del(). Fixes: c0cdc19 ("rpmsg: Driver for user space endpoint interface") Signed-off-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4224cfd ] When bringing down the netdevice or system shutdown, a panic can be triggered while accessing the sysfs path because the device is already removed. [ 755.549084] mlx5_core 0000:12:00.1: Shutdown was called [ 756.404455] mlx5_core 0000:12:00.0: Shutdown was called ... [ 757.937260] BUG: unable to handle kernel NULL pointer dereference at (null) [ 758.031397] IP: [<ffffffff8ee11acb>] dma_pool_alloc+0x1ab/0x280 crash> bt ... PID: 12649 TASK: ffff8924108f2100 CPU: 1 COMMAND: "amsd" ... Freescale#9 [ffff89240e1a38b0] page_fault at ffffffff8f38c778 [exception RIP: dma_pool_alloc+0x1ab] RIP: ffffffff8ee11acb RSP: ffff89240e1a3968 RFLAGS: 00010046 RAX: 0000000000000246 RBX: ffff89243d874100 RCX: 0000000000001000 RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff89243d874090 RBP: ffff89240e1a39c0 R8: 000000000001f080 R9: ffff8905ffc03c00 R10: ffffffffc04680d4 R11: ffffffff8edde9fd R12: 00000000000080d0 R13: ffff89243d874090 R14: ffff89243d874080 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 Freescale#10 [ffff89240e1a39c8] mlx5_alloc_cmd_msg at ffffffffc04680f3 [mlx5_core] Freescale#11 [ffff89240e1a3a18] cmd_exec at ffffffffc046ad62 [mlx5_core] Freescale#12 [ffff89240e1a3ab8] mlx5_cmd_exec at ffffffffc046b4fb [mlx5_core] Freescale#13 [ffff89240e1a3ae8] mlx5_core_access_reg at ffffffffc0475434 [mlx5_core] Freescale#14 [ffff89240e1a3b40] mlx5e_get_fec_caps at ffffffffc04a7348 [mlx5_core] Freescale#15 [ffff89240e1a3bb0] get_fec_supported_advertised at ffffffffc04992bf [mlx5_core] Freescale#16 [ffff89240e1a3c08] mlx5e_get_link_ksettings at ffffffffc049ab36 [mlx5_core] Freescale#17 [ffff89240e1a3ce8] __ethtool_get_link_ksettings at ffffffff8f25db46 Freescale#18 [ffff89240e1a3d48] speed_show at ffffffff8f277208 Freescale#19 [ffff89240e1a3dd8] dev_attr_show at ffffffff8f0b70e3 Freescale#20 [ffff89240e1a3df8] sysfs_kf_seq_show at ffffffff8eedbedf Freescale#21 [ffff89240e1a3e18] kernfs_seq_show at ffffffff8eeda596 Freescale#22 [ffff89240e1a3e28] seq_read at ffffffff8ee76d10 Freescale#23 [ffff89240e1a3e98] kernfs_fop_read at ffffffff8eedaef5 Freescale#24 [ffff89240e1a3ed8] vfs_read at ffffffff8ee4e3ff Freescale#25 [ffff89240e1a3f08] sys_read at ffffffff8ee4f27f Freescale#26 [ffff89240e1a3f50] system_call_fastpath at ffffffff8f395f92 crash> net_device.state ffff89443b0c0000 state = 0x5 (__LINK_STATE_START| __LINK_STATE_NOCARRIER) To prevent this scenario, we also make sure that the netdevice is present. Signed-off-by: suresh kumar <suresh2514@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

Release refcount after xas_set to fix UAF which may cause panic like this: page:ffffea000491fa40 refcount:1 mapcount:0 mapping:0000000000000000 index:0x1 pfn:0x1247e9 head:ffffea000491fa00 order:3 compound_mapcount:0 compound_pincount:0 memcg:ffff888104f91091 flags: 0x2fffff80010200(slab|head|node=0|zone=2|lastcpupid=0x1fffff) ... page dumped because: VM_BUG_ON_PAGE(PageTail(page)) ------------[ cut here ]------------ kernel BUG at include/linux/page-flags.h:632! invalid opcode: 0000 [Freescale#1] SMP DEBUG_PAGEALLOC KASAN CPU: 1 PID: 7642 Comm: sh Not tainted 5.15.51-dirty Freescale#26 ... Call Trace: <TASK> __invalidate_mapping_pages+0xe7/0x540 drop_pagecache_sb+0x159/0x320 iterate_supers+0x120/0x240 drop_caches_sysctl_handler+0xaa/0xe0 proc_sys_call_handler+0x2b4/0x480 new_sync_write+0x3d6/0x5c0 vfs_write+0x446/0x7a0 ksys_write+0x105/0x210 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f52b5733130 ... This problem has been fixed on mainline by patch 6b24ca4 ("mm: Use multi-index entries in the page cache") since it deletes the related code. Fixes: 5c211ba ("mm: add and use find_lock_entries") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b8caf69 upstream. Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on default RX FIFO depth, e.g. 16. Later during serial startup the qcom_geni_serial_port_setup() updates the RX FIFO depth (port->rx_fifo_depth) to match real device capabilities, e.g. to 32. The RX UART handle code will read "port->rx_fifo_depth" number of words into "port->rx_fifo" buffer, thus exceeding the bounds. This can be observed in certain configurations with Qualcomm Bluetooth HCI UART device and KASAN: Bluetooth: hci0: QCA Product ID :0x00000010 Bluetooth: hci0: QCA SOC Version :0x400a0200 Bluetooth: hci0: QCA ROM Version :0x00000200 Bluetooth: hci0: QCA Patch Version:0x00000d2b Bluetooth: hci0: QCA controller version 0x02000200 Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2 Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2) Bluetooth: hci0: QCA Failed to download patch (-2) ================================================================== BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c Write of size 4 at addr ffff279347d578c0 by task swapper/0/0 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty Freescale#26 Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x40 dump_stack_lvl+0x8c/0xb8 print_report+0x188/0x488 kasan_report+0xb4/0x100 __asan_store4+0x80/0xa4 handle_rx_uart+0xa8/0x18c qcom_geni_serial_handle_rx+0x84/0x9c qcom_geni_serial_isr+0x24c/0x760 __handle_irq_event_percpu+0x108/0x500 handle_irq_event+0x6c/0x110 handle_fasteoi_irq+0x138/0x2cc generic_handle_domain_irq+0x48/0x64 If the RX FIFO depth changes after probe, be sure to resize the buffer. Fixes: f9d690b ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2ea3528 upstream. Commit bf5c25d ("skbuff: in skb_segment, call zerocopy functions once per nskb") added the call to zero copy functions in skb_segment(). The change introduced a bug in skb_segment() because skb_orphan_frags() may possibly change the number of fragments or allocate new fragments altogether leaving nrfrags and frag to point to the old values. This can cause a panic with stacktrace like the one below. [ 193.894380] BUG: kernel NULL pointer dereference, address: 00000000000000bc [ 193.895273] CPU: 13 PID: 18164 Comm: vh-net-17428 Kdump: loaded Tainted: G O 5.15.123+ Freescale#26 [ 193.903919] RIP: 0010:skb_segment+0xb0e/0x12f0 [ 194.021892] Call Trace: [ 194.027422] <TASK> [ 194.072861] tcp_gso_segment+0x107/0x540 [ 194.082031] inet_gso_segment+0x15c/0x3d0 [ 194.090783] skb_mac_gso_segment+0x9f/0x110 [ 194.095016] __skb_gso_segment+0xc1/0x190 [ 194.103131] netem_enqueue+0x290/0xb10 [sch_netem] [ 194.107071] dev_qdisc_enqueue+0x16/0x70 [ 194.110884] __dev_queue_xmit+0x63b/0xb30 [ 194.121670] bond_start_xmit+0x159/0x380 [bonding] [ 194.128506] dev_hard_start_xmit+0xc3/0x1e0 [ 194.131787] __dev_queue_xmit+0x8a0/0xb30 [ 194.138225] macvlan_start_xmit+0x4f/0x100 [macvlan] [ 194.141477] dev_hard_start_xmit+0xc3/0x1e0 [ 194.144622] sch_direct_xmit+0xe3/0x280 [ 194.147748] __dev_queue_xmit+0x54a/0xb30 [ 194.154131] tap_get_user+0x2a8/0x9c0 [tap] [ 194.157358] tap_sendmsg+0x52/0x8e0 [tap] [ 194.167049] handle_tx_zerocopy+0x14e/0x4c0 [vhost_net] [ 194.173631] handle_tx+0xcd/0xe0 [vhost_net] [ 194.176959] vhost_worker+0x76/0xb0 [vhost] [ 194.183667] kthread+0x118/0x140 [ 194.190358] ret_from_fork+0x1f/0x30 [ 194.193670] </TASK> In this case calling skb_orphan_frags() updated nr_frags leaving nrfrags local variable in skb_segment() stale. This resulted in the code hitting i >= nrfrags prematurely and trying to move to next frag_skb using list_skb pointer, which was NULL, and caused kernel panic. Move the call to zero copy functions before using frags and nr_frags. Fixes: bf5c25d ("skbuff: in skb_segment, call zerocopy functions once per nskb") Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reported-by: Amit Goyal <agoyal@purestorage.com> Cc: stable@vger.kernel.org Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0b0747d upstream. The following processes run into a deadlock. CPU 41 was waiting for CPU 29 to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29 was hung by that spinlock with IRQs disabled. PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd" !# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0 !# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0 !# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0 # 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0 # 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0 # 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0 # 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0 # 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0 # 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0 # 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0 Freescale#10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0 Freescale#11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0 Freescale#12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0 Freescale#13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0 Freescale#14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0 Freescale#15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0 Freescale#16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0 Freescale#17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0 Freescale#18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0 Freescale#19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd" !# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0 !# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0 # 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0 # 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0 # 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0 # 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0 # 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0 # 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0 # 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0 # 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 Freescale#10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 Freescale#11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 Freescale#12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 Freescale#13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 Freescale#14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 Freescale#15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 Freescale#16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 Freescale#17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 The lock is used to synchronize different sysfs operations, it doesn't protect any resource that will be touched by an interrupt. Consequently it's not required to disable IRQs. Replace the spinlock with a mutex to fix the deadlock. Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230828221018.19471-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7a17308 ] This fixes the circular locking dependency warning below, by reworking iso_sock_recvmsg, to ensure that the socket lock is always released before calling a function that locks hdev. [ 561.670344] ====================================================== [ 561.670346] WARNING: possible circular locking dependency detected [ 561.670349] 6.12.0-rc6+ #26 Not tainted [ 561.670351] ------------------------------------------------------ [ 561.670353] iso-tester/3289 is trying to acquire lock: [ 561.670355] ffff88811f600078 (&hdev->lock){+.+.}-{3:3}, at: iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670405] but task is already holding lock: [ 561.670407] ffff88815af58258 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}, at: iso_sock_recvmsg+0xbf/0x500 [bluetooth] [ 561.670450] which lock already depends on the new lock. [ 561.670452] the existing dependency chain (in reverse order) is: [ 561.670453] -> #2 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}: [ 561.670458] lock_acquire+0x7c/0xc0 [ 561.670463] lock_sock_nested+0x3b/0xf0 [ 561.670467] bt_accept_dequeue+0x1a5/0x4d0 [bluetooth] [ 561.670510] iso_sock_accept+0x271/0x830 [bluetooth] [ 561.670547] do_accept+0x3dd/0x610 [ 561.670550] __sys_accept4+0xd8/0x170 [ 561.670553] __x64_sys_accept+0x74/0xc0 [ 561.670556] x64_sys_call+0x17d6/0x25f0 [ 561.670559] do_syscall_64+0x87/0x150 [ 561.670563] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670567] -> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 561.670571] lock_acquire+0x7c/0xc0 [ 561.670574] lock_sock_nested+0x3b/0xf0 [ 561.670577] iso_sock_listen+0x2de/0xf30 [bluetooth] [ 561.670617] __sys_listen_socket+0xef/0x130 [ 561.670620] __x64_sys_listen+0xe1/0x190 [ 561.670623] x64_sys_call+0x2517/0x25f0 [ 561.670626] do_syscall_64+0x87/0x150 [ 561.670629] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670632] -> #0 (&hdev->lock){+.+.}-{3:3}: [ 561.670636] __lock_acquire+0x32ad/0x6ab0 [ 561.670639] lock_acquire.part.0+0x118/0x360 [ 561.670642] lock_acquire+0x7c/0xc0 [ 561.670644] __mutex_lock+0x18d/0x12f0 [ 561.670647] mutex_lock_nested+0x1b/0x30 [ 561.670651] iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670687] iso_sock_recvmsg+0x3e9/0x500 [bluetooth] [ 561.670722] sock_recvmsg+0x1d5/0x240 [ 561.670725] sock_read_iter+0x27d/0x470 [ 561.670727] vfs_read+0x9a0/0xd30 [ 561.670731] ksys_read+0x1a8/0x250 [ 561.670733] __x64_sys_read+0x72/0xc0 [ 561.670736] x64_sys_call+0x1b12/0x25f0 [ 561.670738] do_syscall_64+0x87/0x150 [ 561.670741] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670744] other info that might help us debug this: [ 561.670745] Chain exists of: &hdev->lock --> sk_lock-AF_BLUETOOTH-BTPROTO_ISO --> sk_lock-AF_BLUETOOTH [ 561.670751] Possible unsafe locking scenario: [ 561.670753] CPU0 CPU1 [ 561.670754] ---- ---- [ 561.670756] lock(sk_lock-AF_BLUETOOTH); [ 561.670758] lock(sk_lock AF_BLUETOOTH-BTPROTO_ISO); [ 561.670761] lock(sk_lock-AF_BLUETOOTH); [ 561.670764] lock(&hdev->lock); [ 561.670767] *** DEADLOCK *** Fixes: 07a9342 ("Bluetooth: ISO: Send BIG Create Sync via hci_sync") Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 073d898 upstream. Syzkaller reported this warning: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 16 at net/ipv4/af_inet.c:156 inet_sock_destruct+0x1c5/0x1e0 Modules linked in: CPU: 0 UID: 0 PID: 16 Comm: ksoftirqd/0 Not tainted 6.12.0-rc5 Freescale#26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:inet_sock_destruct+0x1c5/0x1e0 Code: 24 12 4c 89 e2 5b 48 c7 c7 98 ec bb 82 41 5c e9 d1 18 17 ff 4c 89 e6 5b 48 c7 c7 d0 ec bb 82 41 5c e9 bf 18 17 ff 0f 0b eb 83 <0f> 0b eb 97 0f 0b eb 87 0f 0b e9 68 ff ff ff 66 66 2e 0f 1f 84 00 RSP: 0018:ffffc9000008bd90 EFLAGS: 00010206 RAX: 0000000000000300 RBX: ffff88810b172a90 RCX: 0000000000000007 RDX: 0000000000000002 RSI: 0000000000000300 RDI: ffff88810b172a00 RBP: ffff88810b172a00 R08: ffff888104273c00 R09: 0000000000100007 R10: 0000000000020000 R11: 0000000000000006 R12: ffff88810b172a00 R13: 0000000000000004 R14: 0000000000000000 R15: ffff888237c31f78 FS: 0000000000000000(0000) GS:ffff888237c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffc63fecac8 CR3: 000000000342e000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn+0x88/0x130 ? inet_sock_destruct+0x1c5/0x1e0 ? report_bug+0x18e/0x1a0 ? handle_bug+0x53/0x90 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? inet_sock_destruct+0x1c5/0x1e0 __sk_destruct+0x2a/0x200 rcu_do_batch+0x1aa/0x530 ? rcu_do_batch+0x13b/0x530 rcu_core+0x159/0x2f0 handle_softirqs+0xd3/0x2b0 ? __pfx_smpboot_thread_fn+0x10/0x10 run_ksoftirqd+0x25/0x30 smpboot_thread_fn+0xdd/0x1d0 kthread+0xd3/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]--- Its possible that two threads call tcp_v6_do_rcv()/sk_forward_alloc_add() concurrently when sk->sk_state == TCP_LISTEN with sk->sk_lock unlocked, which triggers a data-race around sk->sk_forward_alloc: tcp_v6_rcv tcp_v6_do_rcv skb_clone_and_charge_r sk_rmem_schedule __sk_mem_schedule sk_forward_alloc_add() skb_set_owner_r sk_mem_charge sk_forward_alloc_add() __kfree_skb skb_release_all skb_release_head_state sock_rfree sk_mem_uncharge sk_forward_alloc_add() sk_mem_reclaim // set local var reclaimable __sk_mem_reclaim sk_forward_alloc_add() In this syzkaller testcase, two threads call tcp_v6_do_rcv() with skb->truesize=768, the sk_forward_alloc changes like this: (cpu 1) | (cpu 2) | sk_forward_alloc ... | ... | 0 __sk_mem_schedule() | | +4096 = 4096 | __sk_mem_schedule() | +4096 = 8192 sk_mem_charge() | | -768 = 7424 | sk_mem_charge() | -768 = 6656 ... | ... | sk_mem_uncharge() | | +768 = 7424 reclaimable=7424 | | | sk_mem_uncharge() | +768 = 8192 | reclaimable=8192 | __sk_mem_reclaim() | | -4096 = 4096 | __sk_mem_reclaim() | -8192 = -4096 != 0 The skb_clone_and_charge_r() should not be called in tcp_v6_do_rcv() when sk->sk_state is TCP_LISTEN, it happens later in tcp_v6_syn_recv_sock(). Fix the same issue in dccp_v6_do_rcv(). Suggested-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Fixes: e994b2f ("tcp: do not lock listener to process SYN packets") Signed-off-by: Wang Liang <wangliang74@huawei.com> Link: https://patch.msgid.link/20241107023405.889239-1-wangliang74@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Alva Lan <alvalan9@foxmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

yishaih and others added 30 commits August 20, 2016 11:53

Linux 3.14.77

bb28cae

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

3.14 1.0.x mx6 sr docker #26

3.14 1.0.x mx6 sr docker #26

bfg2008 commented Mar 17, 2018

3.14 1.0.x mx6 sr docker #26

3.14 1.0.x mx6 sr docker #26

Conversation

bfg2008 commented Mar 17, 2018